02.01

Description
Technical characteristics

02.01

Are designed for liquid, gaseous, and granular media temperature measurement, and also for solid surface temperature measurement.
It is permitted to bend sensors to put hot junction in measuring area, if thermocouple is used in complex-geometry equipment or hard-to-get-at places.
Thermocouple with 3, 4.5mm outer diameter and installed length 20 meters and more, are recommended for power boiler wall temperature monitoring. Maximum installed length of 3mm diameter thermocouple can be equal to 600 m (for pit and well installation). 1.0-1.5mm diameter thermocouples are suitable for research precision high-speed temperature measurement of small-size objects.
Thermocouple wire leads can be lengthened by means of extension lead. Joint is put in reducing sleeve and sealed. Thermocouple clip can be installed at free wire ends.
Movable fittings UNKJ 031 (see section 10) designed for 1.0 MPa rated pressure are used for sensor installation at site. For application area extension CTx 02.01 thermocouples can be manufactured with welded (soldered) mounting elements in compliance with the Customer's drawings.
02.19 and 02.34 modifications are designed for solid surface temperature measurement. 02.19 are fixed to the surface by means of pin, 02.34 end is welded to the surface (see pic. 4 pages 2-15).
Sensors can be of explosion protection type 0ExiaIICT6 X according to GOST 30852.10-2002. For further details see "Alternative designs & Ordering information" below.

If required, thermocouples with 4-20 mА DC signal and/or digital signal via HART, PROFIBUS-PA, FOUNDATION Fieldbus protocol, can be equipped with remote measuring transmitters.

View full

Technical characteristics

Hot junction	one	Ungrounded or Grounded
	two
Vibration resistance GOST R 52931	group V3
Nominal (rated) pressure	0,1MPa without mounting elements		up to 150MPa depending on mounting elements
Seismic resistance MSK-64	*grade 9* for unit installation up to 70 m above zero mark
Climatic category GOST 15150	*UHL2*Ambient temperature:	-60..+120ºС for general purpose products
		-60..+85 ºС for Ex version with analogous signal
Calibration	MI 3090-2007 - for sensor fitting length 20 to 250 mm GOST 8.338-2001 - for sensor fitting length larger than 250 mm

Reliability indicators

Group of operating conditions	Probability of failure-free operation	Specified lifetime	Mean lifetime	Guarantee conditions
I	0.95 for 40 000 hours	5 years	10 years	5 years
II	0.95 for 16 000 hours	2 years	4 years	2 years
III	0.95 for 8 000 hours	1 year	2 years	1 year
IV	Not rated	Not rated	Not rated	Not rated

Temperature range

CT type	Application temperature, ºС	Group of operating conditions	Calibration interval	Cable selection
CT type	Application temperature, ºС	Group of operating conditions	Calibration interval	Sheath diameter	Sheath material
CTK	– 40 .. + 600	I	5 years	3; 4; 4,5; 6	S321; S316; T310; Т446; T600
	– 200 ..+ 600	II	2 years	1.5; 2;	S321; S316; T310; T600
	– 200 ..+ 800			3; 4; 4,5; 6	S321
	– 200..+ 900			3; 4; 4,5; 6	S316; T310; T600
	– 200 ..+ 800	III	1 year	1.5; 2;	S321
	– 200..+ 900			1.5; 2;	S316; T310; T600
	– 200..+ 1000			3	T310; Т446; T600
	– 200..+ 1100			4.5; 6	T310; Т446; T600
	– 40 .. + 700	IV	Not rated	1	S321; T310; T600
	– 40..+ 1300	IV	Not rated	4.5; 6	T600
CTN	– 40 ..+ 800	I	5 years	3; 4.5	Т310; Т600; Т740
	– 200 ..+ 600	II	2 years	1.5; 2	S321
	– 200 ..+ 800			1.5; 2;	Т310; Т600; Т740
	– 200 ..+ 1000			3	T310; T600
	– 200 ..+ 1100			4.5	T310; T600
	– 200 ..+ 1100			3; 4.5	Т740
	– 200 ..+ 800	III	1 year	1.5; 2	S321
	– 200..+ 900			1.5	T310; T600
	– 200 ..+ 1000			1.5; 2	Т740
	– 200 ..+ 1100			3	T310; T600
	– 200 ..+ 1150			4.5	T310; T600
	– 200 ..+ 1200			3; 4.5	Т740
	– 40 ..+ 800	IV	Not rated	1	Т600; Т740
	– 40 ..+ 1300	IV	Not rated	4.5	Т740
CTL	– 40 ..+ 600	I	5 years	3; 4; 4.6; 5; 6	S10
	– 100 . + 800	II	2 years	3; 4; 4.6; 5; 6
	– 100 . + 600	III	1 year	1.5
	– 40 ..+ 600	IV	Not rated	1
CTJ	– 40 ..+ 760	II	2 years	2; 3; 4.5	S321, S316
CTM	– 40 ..+ 200	II	2 years	2; 3; 4.5	S10; S321
CTM	– 200 ..+ 370	III	1 year	2; 3; 4.5	S10; S321

Response time τ 0,63:

Hot junction	Sensor response time depending on diameter, s
Hot junction	d = 0,5	d = 1,0	d = 1,5; 2	d = 3.0	d = 4,0	d = 4,5; 4,6	d = 5,0	d = 6,0
Insulated from sheath	0.05	0.15	0.4	1.0	1.5	2.0	3.0	4.0
Uninsulated from sheath	0.03	0.05	0.15	0.5	1.0	1.0	1.5	2.0

Execution options

*CTK*		*Exi*	*02.01*	—	2	50	—	c1	—	U		—	*Т310*	D	—	3	—	L	/		l	-
1		2	3		4	5		6		7	8		9	10		11		12		13	14		15

NN	Parameter name	Code	Description
1	Sensor type	*CTK, CTL, CTN, CTJ, CTM*	Mineral insulated cable thermocouple with type according to IEC 60584 and ASTM E230
2	Explosion protection	*Not filled*	general purpose electrical equipment
		*Exi*	0ExiaIICT6 X, intrinsically safe circuit
3	Modification describes design features	*02.01*	without mounting elements, basic modification
		*02.02*	without mounting elements, with rolled end
		*02.19*	with bolt fixing ring
		*02.34*	with surface welded element
4	Terminal head	0	Free electrode ends 50mm		IP65 wire 50-69, 80		0ExiaIICT6Х or general purpose
					IP40 wire 70		general purpose
		2	miniature plug		IP40		general purpose
		4	standard plug		IP40		general purpose
5	Wire version (see "Alternative designs" table, pages 1-14)	50	Stranded conductor, silicon / shield / silicon insulation - shield is insulated from sensor body and does not have a terminal
		51	Stranded conductor, silicon / shield / silicon insulation - shield is insulated from sensor body and has a separate terminal
		52	Stranded conductor, silicon / shield / silicon insulation - shield is connected with sensor body and has a separate terminal
		54	solid conductor, silicon / silicon insulation without shield
		60	Stranded conductor, PTFE / shield / PTFE insulation - shield is insulated from sensor body and does not have a terminal
		61	Stranded conductor, PTFE / shield / PTFE insulation - shield is insulated from sensor body and has a separate terminal
		62	Stranded conductor, PTFE / shield / PTFE insulation - shield is connected with sensor body and has a separate terminal
		63	stranded conductor, PTFE / PTFE / outer armour insulated from sensor body
		64	solid conductor, PTFE / PTFE insulation without shield
		70	stranded conductor, conductor insulation and outer glass filament sheath / outer galvanized steel armour
		80	stranded conductor, PTFE insulation, in metal hose
6	Sensor class designation	*c0; c1; c2*	For further details see table 5 page 2-9
7	Hot junction design	О	exposed junction,			general purpose
		G	grounded junction,			general purpose
		U	ungrounded junction			0ExiaIICT6 or general purpose
8	Number of wire couples	*Not filled*	1 wire couple
		2	2 wire couples (2 junctions)
9	Cable outer sheath material	*S10*	Steel 12Cr18Ni10Т (only for CTL)
		*S321*	Steel AISI 321
		*S316*	Steel AISI 316
		*Т310*	Steel AISI 310
		*Т446*	Steel AISI 446
		*Т600*	INCONEL 600
		*Т740*	ALLOY 740
10	Cable sheath thickness	*Not filled*	standard sheath thickness (see table 1 introduction)
		D	double sheath thickness (see table 1 introduction)
11	Outer diameter	1;	size (mm) on Customer's choice	general purpose			02.01
		*1.5; 2*		0ExiaIICT6 or general purpose			02.01
		*3;4; 4,5; 4,6; 5; 6*					02.01, 02.02, 02.19, 02.34
12	Probe length, L	*10÷100,000*	100, 120, 200, 250, 320, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150 and more
13	Number of extension leads	*Not filled*	One extension lead, number of wire couples is stated in item 8					U, U2, G, G2
		2х	Two leads, one wire couple each					U2, except for 80 lead
14	Wire length l	*100÷30 000*	specify dimensions in mm 500, 1000, 2000 3150 and more
15	Additional information	*Not filled*	for 02.01 and 02.02
		*D/d*	outer and inner diameter of 02.19 tip
		*30х10х6*	Welded element size for 01.34

Examples of product designation

*CTK 02.01-050 - c1 – U2 – S321 – 4,5 – 2000/2x3150*	Product type	CT	cable thermocouple
	Type of TC	K	chromel-alumel
	Explosion protection	-	general purpose
	Modification	*02.01*
	Terminal head	0	Free electrode ends
	Wire type	50	silicon / shield / silicon
	Tolerance class	c1	first class
	Junction type	U2	two, ungrounded
	Cable sheath material and thickness	*S321*	steel AISI 321, standard thickness
	Cable diameter	*4.5*	mm
	Probe length	*2000*	mm
	Wire length	*2х3150*	Two wires, 3150mm each
*CTK 02.01-050 - c1 – U2 – S321 – 4,5 – 2000/3150*	Product type	CT	cable thermocouple
	Type of TC	K	chromel-alumel
	Explosion protection	-	general purpose
	Modification	*02.01*
	Terminal head	0	Free electrode ends
	Wire type	50	silicon / shield / silicon
	Tolerance class	c1	first class
	Junction type	U2	two, ungrounded
	Cable sheath material and thickness	*S321*	steel AISI 321, standard thickness
	Cable diameter	*4.5*	mm
	Probe length	*2000*	mm
	Wire length	*2х3150*	one wire 3150mm long with two wire couples
*CTK Exi 02.01-080 - c1 – U – Т310D - 6 – 800/3150*	Product type	CT	cable thermocouple
	Type of TC	K	chromel-alumel
	Explosion protection	*Exi*	0ExiaIICT6 X
	Modification	*02.01*
	Terminal head	0	Free electrode ends
	Wire type	80	PTFE / PTFE / metal hose
	Tolerance class	c1	first class
	Junction type	U	ungrounded, one
	Cable sheath material and thickness	*Т310D*	steel AISI 310, double thickness
	Cable diameter	6	mm
	Probe length	*800*	mm
	Wire length	*3150*	mm